Landscape Kit Includes:

• Four SC-OG-6 Landscape speakers
• Crown CDi DriveCore 2|600 Power amplifier
• 600W x 2 at 4 Ohms
• Pre-loaded with custom DSP curves for landscape speakers and subwoofers
• Simultaneous 70V/100V and 8 Ohm operation
• 2U rack mountable
• Compatible with Harman’s HiQnet Audio Architect software
• Amplifier Dimensions: 483mm x 311mm x 89mm
• SC-OG-6 Dimensions: LxWxH, in/mm: 11.8 x 7.7 x 12 / 300 x 195.6 x 307 with arm

SC-OG-6

6” (152mm) 2-way High-Performance Outdoor Satellite Speaker

Features

• 6″ (152mm) Polypropylene Cone Woofer with NBR Surround
• 3/4″ (20mm) Aluminum Dome Tweeter
• Weather-Resistant Fiberglass-Reinforced ABS Enclosure
• Sensitivity: 87dB
• Frequency Response: 100Hz-20kHz +/- 3dB
• Power Handling: Up to 120W
• Nominal Impedance: 8 ohms (in Bypass Mode)
• Tap Settings: 70V/100V: 3.75W (70V only), 7.5W, 15W, 30W, 8 Ohm (Bypass)
• 110-degree wide dispersion
• Mounting accessories not included

Specifications

Line Voltage: : 70V/100V
Transformer Tap Settings: : 3.75W (70V only), 7.5W, 15W, 30W, 8 Ohm (Bypass)

Other Specifications

Warranty

Limited Lifetime Warranty

---------------------------------------------------

CDi 2|600

Analog input, 2 channel, 600W per output channel

The CDi DriveCore Series is an evolution in amplification, providing an impressive mix of high-performance; rich feature set, and competitive cost. Using technology derived from our flagship Installed Sound amplifier (Crown DriveCore Install series), the CDi DriveCore 2|600 offers streamlined functionality to work in almost any medium sized installation such as cinema, houses of worship, bars, lounges, and more. Designed for ease-of-use in a variety of applications, the 2|600 is a 2-channel amp that includes network control/monitoring, high-level DSP, front-panel interface, and support for driving up to 100Vrms speaker loads without requiring a transformer. The entire CDi DriveCore line comes pre-loaded with JBL speaker tunings to help make installations quicker and easier.

Feature Comparison

Output Power: Dual Mode - All Channels Driven

Minimum Guaranteed Power (1kHz, all channels driven, max distortion 0.5%, duration 0.5 seconds, 120 - 240Vrms - 50/60Hz)

Output Power: Bridge Mono Mode - All Channels Driven

Minimum Guaranteed Power (1kHz, all channels driven, max distortion 0.5%, duration 0.5 seconds, 120 - 240Vrms - 50/60Hz)

Features

DriveCore Technology – Crown’s proprietary DriveCore technology eliminates hundreds of components within each amplifier, reducing the variability of component values, increasing reliability, resulting in incredible audio fidelity from an efficient design.

Network Control and Monitoring – Through Harman’s HiQnet Audio Architect software, the CDi DriveCore can be controlled, configured, and monitored through standard TCP/IQ network.

DSP – On-board Digital Signal Processor in each amplifier allows for custom configuration

• Input Router
• Input Delay – Up to 1000ms
• Input Parametric EQ – 8 band
• Crossover
• Output Parametric EQ – 8 band
• Output Delay – Up to 100ms
• LevelMAX™ Limiter

BLU link (BL models only) – Both receive and send channels over HARMAN’s 256 channel, fault-tolerant audio BUS, BLU link

Direct Drive 70/100Vrms Output – Each output channel is capable of provide either 70V or 100V for high impedance applications.

Front-Panel Interface – Completely configure the amplifier using an intuitive front-panel interface.

GPIO/AUX Port – Recall presets, mute channels, monitor faults, power on/off the amplifier, and more through a combined GPIO/AUX Port.

Specifications